2001 Chevrolet Monte Carlo

General Motors LLC (GM) is recalling certain model year 1998-1999 Chevrolet Lumina and Oldsmobile Intrigue, 1997-2004 Buick Regal and Pontiac Grand Prix, 2000-2004 Chevrolet Impala, and 1998-2004 Chevrolet Monte Carlo vehicles. The affected vehicles were previously repaired under recalls 08V-118, 09V-116, and 15V-201 to address the possibility that engine oil may drip onto the hot exhaust manifold.

Fix: The remedy applied under recalls 08V-118, 09V-116, and 15V-201 did not adequately remove the safety risk. Under the improved remedy, dealers will replace the engine’s front valve cover and gasket. Vehicles that are covered by recalls 08V-118, 09V-116, or 15V-201 that have not yet received the ori…

This defect can affect the safe operation of the airbag system. Until this recall is performed, customers should remove all items from their key rings, leaving only the ignition key. The key fob (if applicable), should also be removed from the key ring. General Motors LLC (GM) notified the agency on July 3, 2014, that they are recalling 5,877,718 model year 2000-2005 Chevrolet Impala and Monte Carlo, 1997-2003…

Fix: GM will notify owners, and dealers will install two key rings and an insert in the key slot or a cover over the key head on all ignition keys, free of charge. The recall began on September 9, 2014. GM's number for this recall is 14350.

GENERAL MOTORS IS RECALLING 1,497,516 MY 1997-2003 BUICK REGAL, MY 1998-2003 CHEVROLET LUMINA, MONTE CARLO AND IMPALA, MY 1998-1999 OLDSMOBILE INTRIGUE, MY 1997-2003 PONTIAC GRAND PRIX VEHICLES EQUIPPED WITH A 3.8L V6 NATURALLY ASPIRATED ENGINE. SOME OF THESE VEHICLES HAVE A CONDITION IN WHICH DROPS OF ENGINE OIL MAY BE DEPOSITED ON THE EXHAUST MANIFOLD THROUGH HARD BRAKING.

Fix: DEALERS WILL REPLACE THE ENGINE’S FRONT VALVE COVER AND FRONT-VALVE-COVER GASKET WITH NEW PARTS OF AN IMPROVED DESIGN AND REMOVE THE ENGINE’S PLASTIC COVER AND PLASTIC OIL-FILL-TUBE EXTENSION, FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN DURING MAY 2016. OWNERS MAY CONTACT CHEVROLET AT 1-800-6…

DORMAN IS RECALLING 979 STEERING KNUCKLES, DORMAN P/NOS. 697-902 AND 697-903, SOLD UNDER DORMAN'S "OE SOLUTIONS<SUP>TM</SUP>" BRAND NAME, AND NAPA P/NOS. 7-8502 AND 7-8503 WHICH WERE SOLD FOR REPLACEMENT USE ON THE VARIOUS VEHICLES LISTED ABOVE. A POTENTIAL MATERIAL OR DESIGN DEFECT COULD RESULT IN THE STEERING KNUCKLE BREAKING IN THE HUB AREA.

Fix: DORMAN WILL NOTIFY OWNERS AND REPLACE THE DEFECTIVE STEERING KNUCKLES FREE OF CHARGE AND REIMBURSE THE REPAIR FACILITY OR OWNER FOR LABOR. THE RECALL BEGAN ON FEBRUARY 23, 2009. OWNERS MAY CONTACT DORMAN'S TOLL-FREE HOTLINE AT 1-800-523-2492 AND PRESS 5.

DORMAN PRODUCTS IS RECALLING 3,900 INTERMEDIATE STEERING SHAFTS DORMAN PART NOS. 425-151, 425-152, AND 425-153, (SOLD UNDER DORMAN'S "OE SOLUTIONS" BRAND NAME), BALKAMP #'S 7-3057, 7-3058, 7-3059 (SOLD UNDER THE "NAPA" BRAND NAME), AND PLATINUM PARTS #'S 2425151, 2425152, AND 2425153 MANUFACTURED DURING THE MONTH OF SEPTEMBER 2007. THESE REPLACEMENT STEERING SHAFTS CAN BE USED ON THE VEHICLES LISTED ABOVE. THE WEL…

Fix: DORMAN WILL NOTIFY OWNERS AND REPLACE THE STEERING SHAFTS FREE OF CHARGE. THE RECALL BEGAN ON OCTOBER 16, 2008. OWNERS MAY CONTACT DORMAN TOLL FREE AT 1-800-523-2492.

CERTAIN DELPHI FUEL PRESSURE REGULATORS, P/NOS. FP10020-11B1, FP10026-11B1, AND FP10027-11B1, SOLD AFTER JANUARY 9, 2007, AS AFTERMARKET EQUIPMENT FOR VARIOUS PASSENGER VEHICLES LISTED ABOVE. THE UNIVERSAL PRESSURE REGULATORS (UPR) WERE PRODUCED WITHOUT AN O'RING AND RETAINER.

Fix: DELPHI WILL NOTIFY OWNERS AND REPLACE THE UPR FREE OF CHARGE. THE RECALL BEGAN ON APRIL 23, 2007. OWNERS CAN CONTACT DELPHI AT 877-411-8770.

VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE AIR BAG SENSING AND DIAGNOSTIC MODULES (SDM) COULD EXPERIENCE A MEMORY ERROR RESULTING IN THE AIR BAGS NOT DEPLOYING IN A CRASH SITUATION.

Fix: DEALERS WILL REPLACE THE SENSING AND DIAGNOSTIC MODULE.

VEHICLE DESCRIPTION: PASSENGER VEHICLES, LIGHT DUTY TRUCKS, SPORT UTILITY VEHICLES, AND MINI VANS EQUIPPED WITH TRW SEAT BELT BUCKLE ASSEMBLIES. THE BUCKLE BASE OF THESE SEAT BELT ASSEMBLIES WERE NOT PROPERLY HEAT TREATED AND THEREFORE DO NOT PASS THE LOAD BEARING REQUIREMENT OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 209, "SEAT BELT ASSEMBLIES."

Fix: DEALERS WILL INSPECT THE VEHICLE'S SAFETY BELT BUCKLE ASSEMBLY DATE CODES AND, IF NECESSARY, WILL REPLACE ANY SAFETY BELT BUCKLE ASSEMBLY.