2007 Mitsubishi Eclipse Spyder

Mitsubishi Motors North America, Inc. (MMNA) is recalling certain model year 2006-2009 Eclipse vehicles manufactured April 20, 2005, to February 13, 2009, and 2007-2009 Eclipse Spyder vehicles manufactured December 23, 2005, to February 13, 2009. Due to corrosion inside the antil-lock brake system (ABS) unit, one or more of the internal valves may seize. In a braking event that uses the ABS, a seized valve would inc…

Fix: MMNA will notify owners, and dealers will inspect, flush and clean the ABS hydraulic unit using high grade brake fluid, free of charge. If the inspection shows that the valves may seize, the ABS unit will be replaced. The recall began on July 21, 2015. Owners may contact MMNA customer service at 1-…

MITSUBISHI IS RECALLING 45,988 MY 2005-2007 ENDEAVOR, GALANT, ECLIPSE COUPE, AND MY 2007 ECLIPSE SPYDER VEHICLES. THE BRACKET THAT IS THE ATTACHMENT POINT FOR THE LEFT REAR FUEL TANK MOUNTING STRAP MAY HAVE BEEN IMPROPERLY FORMED DURING A METAL STAMPING PROCESS. THE PROCESS MAY HAVE CAUSED THE METAL TO HAVE A SPLIT IN THE AREA WHERE THE BOLT THAT HOLDS ONE OF THE TWO FUEL TANK STRAPS TO THE UNDERSIDE OF THE VEHICLE …

Fix: DEALERS WILL INSPECT TO SEE IF THE LEFT REAR FUEL TANK STRAP MOUNTING BRACKET HAS SPLITTING BEYOND A SPECIFIC LIMIT. VEHICLES WITH MODERATE TO SEVERE SPLITTING WILL BE REPAIRED USING A REINFORCEMENT CAP, A SPECIAL STRUCTURAL ADHESIVE, AND A RIVET TO REINFORCE THE FUEL TANK MOUNTING BRACKET. THE REC…

ON CERTAIN VEHICLES EQUIPPED WITH AUTOMATIC TRANSMISSIONS, THE KEY LOCK CABLE WAS IMPROPERLY MANUFACTURED AND MAY NOT ALLOW THE CABLE END TO LOCK INTO THE FLOOR SHIFTER MECHANISM. THIS CAN RESULT IN THE INTERLOCK SYSTEM TO BECOME INOPERATIVE AND ALLOW THE IGNITION KEY TO BE REMOVED WITHOUT THE GEARSHIFT MECHANISM BEING PLACED IN THE PARK POSITION.

Fix: DEALERS WILL INSPECT THE IGNITION INTERLOCK CABLE AND REPLACE IT IF NECESSARY. THE RECALL BEGAN ON NOVEMBER 20, 2006. OWNERS MAY CONTACT MITSUBISHI AT 1-888-648-7820.

ON CERTAIN PASSENGER VEHICLES, THE METAL FORMING PART OF THE FRONT CROSSMEMBER MAY HAVE BEEN IMPROPERLY STAMPED RESULTING IN THE METAL BECOMING THINNER IN THE CROSS-SECTION THAN SPECIFIED. THIS COULD, OVER TIME, RESULT IN BREAKAGE OF THE CROSSMEMBER.

Fix: DEALERS WILL INSPECT AND REPLACE THE CROSSMEMBER FREE OF CHARGE. THE RECALL BEGAN ON SEPTEMBER 21, 2006. OWNERS MAY CONTACT MITSUBISHI AT 888-648-7820.

Brakes

On certain vehicles, corrosion may occur in the ABS hydraulic unit due to a reaction between the brake fluid and the surface treatment of the internal valves. If this were to occur and the ABS hydraulic unit is activated, one or more of the valves could seize. This could result in longer brake pedal travel and increased stopping distances, which may increase the risk of a crash…

Other

On certain vehicles, the bracket that is the anchor point for the left rear fuel tank mounting strap may have been improperly formed during the manufacturing process. This may have caused the metal to spilt in the area where the bolt holds the fuel strap to the underside of the vehicle. In the event the tank is full of fuel and the vehicle is involved in a serious collision the…

Other

On certain vehicles, the ignition key interlock cable may have been improperly manufactured. This could allow the automatic transmission gear selector lever to be moved out of the PARK position with the key removed from the ignition switch. If the park brake is not applied, and the gear shift lever is moved out of PARK, the vehicle may roll and result in a vehicle crash. Correc…

Structure

On certain vehicles, the right rear portion of the front crossmember is under-strength. This could allow the passenger side lower control arm to separate from the crossmember, which may result in a loss of steering control and a crash. Correction: Dealers will replace the lower crossmember as necessary.